Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing happened? Peek within the tank, and you may see no water inside. Before you stress, relax knowing that repairing this issue is usually straightforward. If you can’t do it yourself, you can always arrange toilet repair with an Expert plumber. Follow these guidelines to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first move is to verify that the water is turned on. If you or someone in your household recently did a toilet repair, you probably turned off the water first. Did you neglect to turn it back on? To find out, turn the water shut-off valve on the wall behind the toilet. If the valve was turned off, water will now start refilling the tank. If this doesn’t work, turn on the water at your sink or a different plumbing fixture. If nothing comes out from the tap, you could possibly have a bigger water supply issue. Call your water company to learn more. 

Reposition or Replace the Float Mechanism 

Older toilet models use a float ball to measure the water level as it goes up in the tank. When the ball passes a specified height, the float arm it’s connected to stops the water flow. However, insufficient water might enter the tank if the ball is positioned wrong or the arm is damaged. To move the float ball, start by removing the toilet tank lid. Bend the float arm up a little to alter where it sits in the tank. If this doesn’t fix the problem, you may need to replace the whole float mechanism. You should be able to complete this yourself by following the directions that come with the replacement parts, or you can employ a plumber for help. Just understand that float balls are old toilet technology. You may appreciate improved reliability and efficiency if you upgrade the existing tank components or replace the toilet altogether. 

Adjust the Fill Valve 

More recent toilets operate with a float cup rather than a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become clogged. Here are some to attempt: 

• Modify the fill valve: Look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly ahered to the tube. Then, change the water level. Newer toilets have an adjustment knob you can turn by hand, while older designs may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to check the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other debris might be blocking the valve and stopping your toilet from filling. Shut down the water behind the toilet and take off the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to block water from spraying everywhere. After several seconds, turn the water back off. Finally, wash the fill cap to clear away hard water buildup. If the cap is broken, buy a new one. 
• Clean the valve tube: The tube below the fill valve could also be plugged. Shut off the water and take off the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the junk. Replace the valve hardware and flush the toilet to test your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve followed the steps above without success, the one remaining possibility is a broken trip assembly. This element connects the flush handle to the tank. If it’s broken or positioned improperly, the flush cycle may not complete, leaving the tank void. Remove the toilet tank lid and examine the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or busted, change it out. Whether you finish the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water again. 

Schedule Toilet Repair Today 

You can’t go long without a reliable toilet, so phone [Company name] to request a toilet repair. We can determine why your toilet isn’t filling and propose the appropriate fix. If your plumbing fixture is old and worn out, our team will install a high-efficiency toilet in your bathroom. Rest assured that every plumbing repair and replacement we perform is backed by a 100% satisfaction guarantee. To schedule an appointment from one of our licensed team members, please call your local Service Experts Heating, Air Conditioning & Plumbing office today.