How to Drain Your Water Heater: A Step-by-Step Guide 

Tank water heaters are a dependable way to secure a fast supply of hot water for your home. The presence of a storage tank ensures some hot water is always available. But over time, foreign substances may accumulate within the storage tank. This might be sediment or mineral buildup originating from the main water line or an opening in the pipes. Whatever the culprit is, this buildup can negatively impact the efficiency of water heaters. In severe cases it can clog up drainage and could even result in premature failure.

Thankfully, draining your water heater and clearing out sediment buildup is a relatively simple task. An experienced plumber in the U.S. can handle the process, but you can also drain the tank on your own if you know what you’re doing. Either way, draining the tank now can help reduce the risk you’ll need premature water heater replacement.

Before You Begin…

Before you start draining the tank, you’ll need to shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you might need to drain the tank more often if you do), the water main supplies all the potable water your home uses. Keeping the valve closed will stop more water from reaching the tank, allowing you to completely empty it.

You’ll also want to fetch a rubber hose, like one you can use for yard work. The hose allows you to safely drain the water heater tank without spilling water all over your garage, utility closet, attic or wherever the water heater is kept. Make sure you put the other end of the hose far away from your home to prevent the water from seeping back inside.

Finally, a screwdriver should help you loosen tight screws or valves. You shouldn’t need any more tools than this unless you stumble upon a problem with the water heater or nearby piping. At that point, it might be best to hire a certified plumber in the U.S..

Step 1: Shut Off the Water Heater

After you’ve shut off the water supply, you can shut off the water heater itself. This will be on the thermostat for natural gas water heaters or through a breaker switch for electric models. The pilot setting on gas water heaters can remain on during flushing, but electric models must be completely off. This is due to the heating elements electric water heaters have, which remain submerged. In an empty tank, they can quickly overheat. You should also check the model’s manual, as some water heaters have to be completely full before the heating elements are started.

Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It may be hours before the water cools to a safe temperature, so it is usually best to leave the rest of the process for the following day.

Step 2: Connect the Hose to the Water Heater’s Drain Valve

Tank water heaters are designed with a drain valve you can use to empty the storage tank. Once you’re sure the water supply is disconnected and the water heater itself is off, locate the drain valve. Some models might have it covered up. Make sure the hose is secure to prevent spilling hot water near you and the water heater.

Step 3: Open a Faucet or Other Hot Water Tap

Your home’s plumbing uses pressure within the piping to maintain a consistent flow of water from the main water line to the rest of the house. This pressure needs to be relieved before the hot water can actually drain out of the tank. By heading to the closest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before returning to the water heater.

Step 4: Release the Drain Valve

Keep in mind that this water may still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should carry sediment buildup out of the tank and away from your home. But some buildup might be stuck to the inside of the tank. Turning the cold water supply back on will help wash away stubborn minerals and other substances from the tank.

Repeat this step until the water appears clear of sediment or minerals. If the drain isn’t working because of a clog, a trained plumber may be required.

Step 5: Re-Shut the Valve Before Refilling the Water Heater

If everything proceeds like it’s supposed to, you should be able to remove most excess sediment stuck inside your water heater. Seal up the drain valve, detach the hose and open the water supply to get things working again. As the water heater tank begins to fill, head back to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back at appropriate levels.

At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned before, don’t forget that some models may need to be totally full before the water can be safely heated. Make sure you review your manufacturer’s instructions before starting the process.

Keep Your Water Heater Sediment-Free for Best Results

Tank water heaters are still a great option for supplying your hot water needs. Draining the tank every 1-2 years will help remove sediment buildup and keep things running at maximum efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in the U.S. from a technician you trust.

Savings For You

See All Offers Here >
parts and labor icon

$50 OFF Any Repair

  • Save $50 on a Paid Service
  • Written 100% Satisfaction Guarantee
  • Plus, ask how to save an additional 15% and waive your trip charge!

Make No Payments for 30 Days!

  • Upgrade to Worry-Free Comfort with the Advantage Program and make NO payments for 30 days!

© 2023 Service Experts, Service Experts Heating & Air Conditioning, and the Service Experts logo and design are registered trademarks of Service Experts LLC and used under license by SE Canada Inc. All Rights Reserved. *Not applicable to the Advantage Program. See your signed Advantage Program Agreement for full details and exclusions. 100% Satisfaction Guarantee is subject to certain restrictions and limitations as set forth in the applicable Terms and Conditions.